FENN MODEL 121 - 12.500" DIA. X 14.000" WIDE 2-HIGH ROLLING MILL - AS-IS CONDITION
The FENN Model 121 is a heavy-duty industrial 2-High rolling mill previously utilized for processing steel bearing material for the automotive industry. The machine is offered with its original payoff, recoiler, and associated hydraulic equipment, providing a substantial foundation for refurbishment, modernization, or integration into a complete coil-to-coil rolling system.
International Rolling Mills (IRM) acquired the equipment through a surplus auction following its removal from production. The mill has not been operated, refurbished, or recommissioned by IRM since acquisition.
The equipment is offered in its existing as-is, where-is condition. IRM can also refurbish, re-engineer, and upgrade the mill to suit a customer's specific rolling application.
EQUIPMENT OVERVIEW & TECHNICAL SPECIFICATIONS
The FENN Model 121 features a heavy-duty four-column housing with approximately 444 square inches of total column cross-sectional area and an estimated separating-force capacity of approximately 840,000 lbf.
Mill Specifications:
- Manufacturer: FENN
- Model: 121
- Configuration: 2-High
- Nominal Roll Diameter: 12.500"
- Mill Head Roll-Width Capacity: 14.000"
- Existing Roll Face Width: Approximately 9.875"
- Roll Journal Diameter: 9.000"
- Individual Column Section: 9.875" x 11.250"
- Total Column Cross-Sectional Area: Approximately 444 square inches
- Mill Separating Force: Approximately 840,000 lbf
- Main Drive: 125 HP DC
- Original Electrical Supply: 480V AC, 3-Phase
- Main Gear Reducer Ratio: 58.01:1
- Screwdown Arrangement: Hydraulic
The mill was originally designed to accommodate nominal 12.500" diameter x 14.000" face rolls. The existing rolls were modified to approximately 9.875" face width for the previous rolling application. New rolls may be manufactured to utilize the full 14.000" face-width capacity, subject to confirmation of the required roll geometry, bearing interfaces, and mechanical clearances.
The mill is currently configured for 2-High rolling due to its existing hydraulic screwdown arrangement and available mill-window space.
EXISTING ROLLS & SPARE SETS
The machine is supplied with its existing rolls, together with two additional spare sets.
The included rolls, along with the available original FENN engineering drawings, provide useful physical and dimensional references for manufacturing replacement rolls. The existing rolls may also be suitable for initial equipment setup, testing, or use as emergency spares, depending on their condition and suitability for the intended application.
All existing rolls are supplied in their present condition without regrinding or refurbishment by IRM.
EXISTING MAIN DRIVE & SPEED REDUCER
The mill is equipped with a Cutler-Hammer 125 HP DC main-drive motor and a heavy-duty Horsburgh & Scott speed reducer.
Cutler-Hammer DC Motor Specifications:
- Manufacturer: Cutler-Hammer / General Electric
- Rated Horsepower: 125 HP
- Motor Type: Stabilized Shunt DC
- Armature Voltage: 500 VDC
- Armature Current: 202 Amps
- Rated Speed: 1,750 / 2,100 RPM
- Field Voltage: 300 VDC
- Duty: Continuous
- Insulation Class: F
- Enclosure: Open, Force Ventilated
Horsburgh & Scott Speed Reducer Specifications:
- Manufacturer: Horsburgh & Scott
- Type: Mark II Helical Speed Reducer
- Size: 170-T/12 1/2
- Reduction Ratio: 58.01:1
- Nameplate Horsepower Rating: 125 HP
- Rated Input Speed: 1,750 RPM
- Service Factor: 1.43
- Oil Capacity: Approximately 67.5 U.S. Gallons
The existing motor, speed reducer, and associated mechanical drivetrain components are supplied in their present condition.
HYDRAULIC SCREWDOWNS & ELECTRICAL EQUIPMENT
The mill retains its existing hydraulic screwdown arrangement from the previous rolling installation.
The original electrical installation utilized a 480V AC, 3-phase power supply. Two large electrical cabinets are available with the mill:
- Cutler-Hammer DC drive cabinet for the 125 HP main-drive motor
- Electrical cabinet associated with the original Vollmer thickness measurement system
The previous installation incorporated automatic gauge-control equipment; however, the original operator station, including the Vollmer gauge display, has been removed and is not included.
The hydraulic and electrical equipment has not been operationally tested or verified for completeness by IRM. Additional controls, operator interfaces, wiring, instrumentation, or modifications may be required to return the mill to operation.
ORIGINAL PAYOFF, RECOILER & HYDRAULIC EQUIPMENT
The mill is offered with its original payoff and recoiler, which were previously utilized alongside the FENN Model 121 for processing steel bearing material for the automotive industry.
Additional Equipment:
- (1) 24" diameter recoiler, 10,000 lb capacity, equipped with a 25 HP DC motor
- (1) 10,000 lb capacity payoff, equipped with a 10 HP DC motor
- (1) Hydraulic power supply
These components provide an opportunity to reestablish a coil-to-coil rolling arrangement or incorporate the equipment into a modernized rolling system.
For customers who do not require the payoff and recoiler, IRM can offer the rolling mill head separately. Please contact us to discuss the desired equipment configuration and pricing.
All equipment is offered in its existing as-is condition and has not been operationally tested by IRM since acquisition.
ORIGINAL FENN ENGINEERING DOCUMENTATION
The mill includes an extensive collection of original FENN engineering documentation, including mechanical drawings, blueprints, technical information, and a service manual.
These materials provide valuable references for maintenance, refurbishment, replacement component manufacturing, and future engineering modifications. Documentation is supplied as available and is not represented as a complete or current set of as-built drawings.
AVAILABLE REFURBISHMENT & CUSTOMIZATION
In addition to offering the machine in its existing condition, International Rolling Mills can refurbish, modernize, and customize the FENN Model 121 to suit a customer's specific rolling requirements.
Potential upgrades include:
- New or reconditioned rolls manufactured for the intended material and application
- Modern AC main-drive motor and variable frequency drive
- Updated electrical controls, PLC, and touchscreen HMI
- Hydraulic screwdown refurbishment or modernization
- Roll-heating equipment and temperature controls
- Load cells, instrumentation, and process monitoring
- Updated guarding, safety systems, and material-handling equipment
- Payoff and recoiler refurbishment or modernization
IRM can work with the customer to determine the appropriate scope of refurbishment and upgrades based on the intended rolling process, budget, and production requirements.
All refurbishment, modernization, and customization services are available by separate quotation.
EQUIPMENT CONDITION & SALE TERMS
The FENN Model 121 and associated equipment are offered as-is, where-is, in their present mechanical, hydraulic, and electrical condition at International Rolling Mills' facility in Pawtucket, Rhode Island.
The equipment has not been operated or tested by IRM since acquisition. Information regarding its previous operating history is provided for reference and does not constitute a guarantee of present operating condition.
Prospective purchasers are encouraged to inspect the equipment prior to purchase. No Factory Acceptance Test, operational demonstration, or commissioning is included in the as-is sale.
The equipment is offered without warranty or guarantee of mechanical condition, operating performance, fitness for a particular application, or ability to achieve specified rolling results, subject to the applicable terms and conditions of sale.
REPRESENTATIVE IMAGES
Photographs provided show the FENN Model 121 rolling mill and associated equipment. Certain historical photographs may depict components from the previous installation, including the original operator station, that are no longer available and are not included in the sale.
The equipment will be supplied in its present condition, subject to the final agreed scope of supply.
FENN MODEL 121 - 12.500" DIA. X 14.000" WIDE 2-HIGH ROLLING MILL - AS-IS CONDITION
The FENN Model 121 is a heavy-duty industrial 2-High rolling mill previously utilized for processing steel bearing material for the automotive industry. The machine is offered with its original payoff, recoiler, and associated hydraulic equipment, providing a substantial foundation for refurbishment, modernization, or integration into a complete coil-to-coil rolling system.
International Rolling Mills (IRM) acquired the equipment through a surplus auction following its removal from production. The mill has not been operated, refurbished, or recommissioned by IRM since acquisition.
The equipment is offered in its existing as-is, where-is condition. IRM can also refurbish, re-engineer, and upgrade the mill to suit a customer's specific rolling application.
EQUIPMENT OVERVIEW & TECHNICAL SPECIFICATIONS
The FENN Model 121 features a heavy-duty four-column housing with approximately 444 square inches of total column cross-sectional area and an estimated separating-force capacity of approximately 840,000 lbf.
Mill Specifications:
- Manufacturer: FENN
- Model: 121
- Configuration: 2-High
- Nominal Roll Diameter: 12.500"
- Mill Head Roll-Width Capacity: 14.000"
- Existing Roll Face Width: Approximately 9.875"
- Roll Journal Diameter: 9.000"
- Individual Column Section: 9.875" x 11.250"
- Total Column Cross-Sectional Area: Approximately 444 square inches
- Mill Separating Force: Approximately 840,000 lbf
- Main Drive: 125 HP DC
- Original Electrical Supply: 480V AC, 3-Phase
- Main Gear Reducer Ratio: 58.01:1
- Screwdown Arrangement: Hydraulic
The mill was originally designed to accommodate nominal 12.500" diameter x 14.000" face rolls. The existing rolls were modified to approximately 9.875" face width for the previous rolling application. New rolls may be manufactured to utilize the full 14.000" face-width capacity, subject to confirmation of the required roll geometry, bearing interfaces, and mechanical clearances.
The mill is currently configured for 2-High rolling due to its existing hydraulic screwdown arrangement and available mill-window space.
EXISTING ROLLS & SPARE SETS
The machine is supplied with its existing rolls, together with two additional spare sets.
The included rolls, along with the available original FENN engineering drawings, provide useful physical and dimensional references for manufacturing replacement rolls. The existing rolls may also be suitable for initial equipment setup, testing, or use as emergency spares, depending on their condition and suitability for the intended application.
All existing rolls are supplied in their present condition without regrinding or refurbishment by IRM.
EXISTING MAIN DRIVE & SPEED REDUCER
The mill is equipped with a Cutler-Hammer 125 HP DC main-drive motor and a heavy-duty Horsburgh & Scott speed reducer.
Cutler-Hammer DC Motor Specifications:
- Manufacturer: Cutler-Hammer / General Electric
- Rated Horsepower: 125 HP
- Motor Type: Stabilized Shunt DC
- Armature Voltage: 500 VDC
- Armature Current: 202 Amps
- Rated Speed: 1,750 / 2,100 RPM
- Field Voltage: 300 VDC
- Duty: Continuous
- Insulation Class: F
- Enclosure: Open, Force Ventilated
Horsburgh & Scott Speed Reducer Specifications:
- Manufacturer: Horsburgh & Scott
- Type: Mark II Helical Speed Reducer
- Size: 170-T/12 1/2
- Reduction Ratio: 58.01:1
- Nameplate Horsepower Rating: 125 HP
- Rated Input Speed: 1,750 RPM
- Service Factor: 1.43
- Oil Capacity: Approximately 67.5 U.S. Gallons
The existing motor, speed reducer, and associated mechanical drivetrain components are supplied in their present condition.
HYDRAULIC SCREWDOWNS & ELECTRICAL EQUIPMENT
The mill retains its existing hydraulic screwdown arrangement from the previous rolling installation.
The original electrical installation utilized a 480V AC, 3-phase power supply. Two large electrical cabinets are available with the mill:
- Cutler-Hammer DC drive cabinet for the 125 HP main-drive motor
- Electrical cabinet associated with the original Vollmer thickness measurement system
The previous installation incorporated automatic gauge-control equipment; however, the original operator station, including the Vollmer gauge display, has been removed and is not included.
The hydraulic and electrical equipment has not been operationally tested or verified for completeness by IRM. Additional controls, operator interfaces, wiring, instrumentation, or modifications may be required to return the mill to operation.
ORIGINAL PAYOFF, RECOILER & HYDRAULIC EQUIPMENT
The mill is offered with its original payoff and recoiler, which were previously utilized alongside the FENN Model 121 for processing steel bearing material for the automotive industry.
Additional Equipment:
- (1) 24" diameter recoiler, 10,000 lb capacity, equipped with a 25 HP DC motor
- (1) 10,000 lb capacity payoff, equipped with a 10 HP DC motor
- (1) Hydraulic power supply
These components provide an opportunity to reestablish a coil-to-coil rolling arrangement or incorporate the equipment into a modernized rolling system.
For customers who do not require the payoff and recoiler, IRM can offer the rolling mill head separately. Please contact us to discuss the desired equipment configuration and pricing.
All equipment is offered in its existing as-is condition and has not been operationally tested by IRM since acquisition.
ORIGINAL FENN ENGINEERING DOCUMENTATION
The mill includes an extensive collection of original FENN engineering documentation, including mechanical drawings, blueprints, technical information, and a service manual.
These materials provide valuable references for maintenance, refurbishment, replacement component manufacturing, and future engineering modifications. Documentation is supplied as available and is not represented as a complete or current set of as-built drawings.
AVAILABLE REFURBISHMENT & CUSTOMIZATION
In addition to offering the machine in its existing condition, International Rolling Mills can refurbish, modernize, and customize the FENN Model 121 to suit a customer's specific rolling requirements.
Potential upgrades include:
- New or reconditioned rolls manufactured for the intended material and application
- Modern AC main-drive motor and variable frequency drive
- Updated electrical controls, PLC, and touchscreen HMI
- Hydraulic screwdown refurbishment or modernization
- Roll-heating equipment and temperature controls
- Load cells, instrumentation, and process monitoring
- Updated guarding, safety systems, and material-handling equipment
- Payoff and recoiler refurbishment or modernization
IRM can work with the customer to determine the appropriate scope of refurbishment and upgrades based on the intended rolling process, budget, and production requirements.
All refurbishment, modernization, and customization services are available by separate quotation.
EQUIPMENT CONDITION & SALE TERMS
The FENN Model 121 and associated equipment are offered as-is, where-is, in their present mechanical, hydraulic, and electrical condition at International Rolling Mills' facility in Pawtucket, Rhode Island.
The equipment has not been operated or tested by IRM since acquisition. Information regarding its previous operating history is provided for reference and does not constitute a guarantee of present operating condition.
Prospective purchasers are encouraged to inspect the equipment prior to purchase. No Factory Acceptance Test, operational demonstration, or commissioning is included in the as-is sale.
The equipment is offered without warranty or guarantee of mechanical condition, operating performance, fitness for a particular application, or ability to achieve specified rolling results, subject to the applicable terms and conditions of sale.
REPRESENTATIVE IMAGES
Photographs provided show the FENN Model 121 rolling mill and associated equipment. Certain historical photographs may depict components from the previous installation, including the original operator station, that are no longer available and are not included in the sale.
The equipment will be supplied in its present condition, subject to the final agreed scope of supply.
Imperial
| Roll Diameter | 12.5" |
| Roll Gap Adjustment | Hydraulic Screwdowns |
| Mill Power | 125 HP DC Motor |
| Mill Separating Force | Approximately 840,000 LBS |
| Mill Voltage | 480V |
| Mill Phase | 3-Phase |
| Mill Controls | Electrical controls included. |
We use cookies to improve your experience. Privacy Policy.